i-Repeater

Cloud control and monitoring
Touch screen interface
Alarms
Statisics

Detail :
*Device = any repeater or line-amp
Connection to the internet.
Each device MUST have a CAT5 ethernet cable connected to it for monitoring.
Option #1: These Cat5 cables are installed back to a comon 3G/4G router with a SIM card.
This solution means you are independent of the buildings WIFI/Internet.
Option #2: Plug each device directly into the building network. No Setup (port forwarding) required. This way is easier but you are dependent on the building network.
What monitoring offers you
Registered users (You, Stelladordus, your client (Hotel)) can monitor and control devices in the building.
Alerts:
You can enable 2 primary email alerts:
Alert 1: If devices are plugged out by accident by building staff (or power cut). (You can see the exact device that is plugged out, and its location in the building). All devices have internal battery that keeps internet connection live for
several hours.
2: If devices are strongly attenuating RF due to local RF noise or disturbance, system will alert you. Example: big microwave ovens in a buildings have been known on rare cases to cause RF issues in local vicinity.
Remote Control from any computer/ phone:
-Switch Off/ On/ or Attenuate, individual bands of any device.
-Switch off Power to one or all devices in a building. The devices RF chain is switched off but it is still connected to the internet.
-Reboot devices.
Monitor:
-Up/Downlink Power
-Up/Downlink Gains
-Up/Downlink AGC
-Up/Downlink Oscillations/feedback
-Temperature on PCB board
History:
-All events are logged from initial installation date for each device.
-A long term history graph for Power levels per band. This will allow you to see the effects of atmospheric conditions,or other conditions on the overall system over 1 year.(in development)
-Percentage usage of each band. Example:
800Mhz :60%, 900Mhz :20%, 1800Mhz :5%, 2100Mhz:15% ,2600Mhz :0%
Security and cloud:
The application infrastructure is physically located in AWS (Amazon Web Services) data-center in Europe (Ireland). AWS allows us to benefit from the most stringent security standards AWS holds for their infrastructure and allows one to satisfy many compliance requirements.
Updates:
Server software is tested and updated from time to time. This is only feasible when all services reside under the one server.
Basic kit includes:
1 i-Repeater_LGDWH,
4 internal antennas, 1 external Yagi antenna
4 lengths of SD240 cable (15m)
1 length of SD400 external cable
1 12v, 5A power supply (surge protected and tested)
The system can be extended using more repeaters and line amps to ensure converage in even the largest of
multi-storey buildings.

 

Specification:
Model number: i4-LGDWH
Frequency: 800/900/1800/2100/2600
Remote monitoring: Yes
Frequency Specifications:
Frequency bands(Mhz): (791-862) + (880-960) + (1710-1880) + (1.92-2.17) + (2500-2690)  
Coverage: (1000m2 per antenna X 4) = ~15 rooms  
Number of People: Unlimited  
Gain: Uplink Gp > 50dB Downlink Gp> 60dB
Pass band ripple: < 4dB  
I/O impedance: 50 ohm/SMA female connector  
Max uplink/downlink signal strength: 19dBm / 10dBm  
Ambient Temperature: -30oC to +70oC  
Power supply input: 110 - 240V AC  
Power supply output: 12v DC  
Oscillation Control Automatic  
Level Control: Automatic*  
Uplink Switch Off Yes**  
AGC Range 30db  
Surge protection SMA connectors DC grounded, 12V DC port MOV protected  
Antenna Specifications: Indoor antenna Outdoor antenna
Nominal Gain 6.4dBi / 9.4dBi 10dBi
3dB beam Pattern 60° x 60° 60° x 50°
Bandwidth 790-960MHz + 1710-2700MHz 790-960MHz + 1710-2700MHz
VSWR <1.4 <1.5
Front to Back Ratio > 20dB > 20dB
Polarization Vertical Vertical
Power Rating 50W 50W
Impedance 50-OHM 50-OHM
Termination SMA male N-Female
Cross Pol. Discrimination -20dB -20dB
Dimensions 210 x 180 x 43mm 442 x 205 x 62mm
Weight 0.68kg 1.2kg
Wind velocity 126km/hr 140km/hr
Working temperature -40°C to +65°C -40°C to +65°C
Power Supply Specification:
AC 100-240V 50-60Hz
DC input 12V 3.6A
Typical power usage   33W
Mechanical Specification:
Length 35cm  
Width 30cm  
Depth 4.4cm  
Weight 2kg  
Mounting 6 x 5mm holes for mounting  
 
* Automatically adjusts during installation. Thereafter, automatically adjusts for seasonal variation in pathloss between basestation and outdoor antenna.
** The up-link amplifiers switch off when the repeater is not in use. This reduces the uplink noise to almost zero. When the repeater is in use (eg. phone call being made), the up-link amplifier switches on for the duration of the call and a blue LED switches on indicating this is the case.
Note: Specifications subject to change without notice.

 

Similar category