WCDMA Multi-Carrier High Power Booster System
BMB2100-150-SW02
Smart Coverage Solution System
WCDMA Multi-Carrier High Power Booster System
System advantages
Bravo’s newly introduced Multi-Carrier High Power Outdoor Booster platform provides higher downlink EIRP and improved uplink sensitivity at the same time to extend the coverage of existing networks. This multi-carrier based product platform can also work with customized NODE B to extend capacity of original WCDMA NODE B with a low system total cost. This product platform features:
- Support multi-carrier WCDMA signals amplify
- Downlink output maximum power 150W
- Support flexible downlink Input either duplexed or unduplexed
- Support system full diversity
- Downlink and uplink gain adjustable with wide dynamic range
- 2.0dB uplink noise figure
- Very high system efficiency
- Extensive product monitoring and control (local and remote)
- Centralized system control/display/alarms
- Powered by 48V DC
- Designed for indoor or outdoor installations
- Extensive protection for lightning, voltage surge, and any high failure rate assemblies
- Compact system size and light weight
System Block Diagram
| Specifications: | |
|---|---|
| RX Characteristics | Specification |
| Frequency Range | 1920-1980MHz |
| Instantaneous Bandwidth | 20MHz |
| Max Gain ANT0 & ANT1 | 15±1 dB |
| LNA Adjustable Gain Range | 0~15dB ( 1 dB/step ) |
| Flatness over Frequency | ≤±1dB |
| Noise Figure | ≤2.0dB (typical) |
| Output 1dB Compression (max. Gain) | +15dB |
| Output IP3 (max. Gain) | +23dBm |
| Insert Loss | ≦1.5 dB |
| Return loss(VSWR) | 18dB (1.3:1) |
| TX to RX isolation | >80dB |
| TX Characteristics | Specification |
| Frequency Range | 2110-2170MHz |
| Instantaneous Bandwidth | 20MHz |
| Number of Carriers | Support multi-carriers (2-4 ) |
| Max Output Power ( input NodeB0 & NodeB1 ) | 150W(51.8dBm with PAR 7.5dB) |
| Maximum Input Power | 46dBm |
| Max Gain | 15 ( PA gain range 0 - 15dB ) |
| PA Gain adjustable step | 1dB |
| PA Gain accuracy | ±1 dB |
| Gain Variation Over Temp | ≤±1.5 dB |
| EVM | ≤3% |
| Delay | ≤0.5μs |
| Insert Loss | ≦1.5 dB |
| ACLR（4 WCDMA ) Carriers@ max Gain( PAR 7.5) | ±5MHz: ≤-50dBc ±10MHz: ≤-60dBc |
| Spectrum Masks and Spurious Emissions | 2.515MHz ≤ f_offset < 2.715MHz: ≤ -26 dBm / 30kHz 2.715MHz ≤ f_offset < 3.515MHz: ≤ -27 dBm / 30kHz 3.515MHz ≤ f_offset < 4.0MHz: ≤ -29 dBm / 30kHz 4.0MHz ≤ f_offset < f_offsetmax: -15 dBm / 1MHz |
| System Characteristics | Specification |
| Return loss(VSWR) | |
| NODE B Ports | 18dB (1.3:1) |
| Antenna Ports | 18dB (1.3:1) |
| Bypass Insert Loss | <0.5dB |
| Power Consumption | ≤1200W |
| Impedance ( TX&RX ) | 50 Ohm |
| Alarm & Protection | Over Power Shutdown, Over Temp Shutdown, Over VSWR Shutdown, restart after 5-10 minutes when alarm clear |
| Monitor & Control | Forward Power, Temp, PA Conditions, TX Gain Setting |
| Environmental Characteristics | Specification |
| Operating Temperature Range | -10˚C to +55˚C |
| Cold Start Temperature | 40˚C |
| Storage Temperature | -40˚C to +85˚C |
| IP Rating | IP55 |
| Humidity | 5%～95 |
| Lightning protection | 90V,. 10kA. 8/20μs Pulse with tolerance ±20% (BTS to ANT Port) |
| EMC | ETS 300 342-3 |
| Mechanical Characteristics | Specification |
| Material (chassis and bracket Mounted ) | Steel within powder coating paint & Aluminum Frame |
| Weight | 51Kg |
| Dimensions（H x W x D） | 437mm x 216mm x 706mm |
| Connector | |
| NODE B Ports | 7/16 DIN female |
| ANT Ports | 7/16 DIN female |
| Reliability Characteristics | Specification |
| MTBF | |
| MCPA | 100,000 hours |
| Rectifier | 70,000 hours |
| Other Parts | 150,000 hours |
| Options | Specification |
| Power Input | 48V DC (±10%) |
